Keri-systems RLB-500 User Manual download pdf

INSTR,INST,WOR

Linear P/N: 212902 C

Material: 20 Lb. Mead Bond

Size: 8.500" x 11.000"

Ink: Black

Side 1 of 2

Scale: 1-1

WOR

Wiegand

Output

Receiver

Installation

Instructions

INTRODUCTION

The Model WOR remote radio receiver is designed for use as an access control interface for Linear’s block coded

digital transmitters. The unit receives signals from transmitters, adds a facility code to the data, and sends the

information to the Wiegand input of the access control panel via a 5-wire connection.

Several transmitter and receiver options can be set using the unit’s dipswitches. Three different Wiegand output

formats (26, 30, & 31-bit) are supported. Three receiver options (lockout, hold, & button offset) can be set.

Transmitter buttons on multi-button units can be selectively disabled. The facility code is set using 16 dipswitches.

Three antenna types can be used with this receiver. The local whip antenna (supplied) screws directly on to the

receiver. The directional (EXA-2000) and omni-directional (EXA-1000) remote antennas attach to the receiver’s

antenna input via RG-59 cable and a type “F” connector.

An on-board RADIO RANGE knob allows adjustment of the receiver’s gain. It can be set to limit the maximum

radio range that the receiver can achieve. Two indicators display the receivers performance and operation. The

red RADIO indicator lights when the receiver detects a radio signal. The two color red/green STATUS indicator

lights green when the receiver is sending Wiegand data and during the 1-second post receiver lockout timer (if

receiver lockout is enabled). The indicator turns red when the receiver’s HOLD input (connected to the access

control panel) is active. Receiver test points are provided for listening to the incoming signals with an audio

amplifier.

Power input to the receiver can be either regulated 5 volts or 8-24 volts DC (jumper selected).

The receiver is housed in a weather-resistant enclosure and can be mounted indoors or outdoors. Gaskets and

a weather-tight wiring strain relief seal the unit from the elements.

1. OPEN CASE 2. LOCATE COMPONENTS

3. SET VOLTAGE INPUT JUMPER 4. SET OUTPUT FORMAT & RECEIVER OPTIONS

(760) 438-7000 • FAX (760) 438-7043

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

OPEN CASE FROM

ANTENNA END

REMOVE FOUR

SCREWS AND WASHERS

BOARD SLIDES OUT

FROM 3RD SLOT UP

INSIDE CASE

5. SET TRANSMITTER FACILITY CODE 6. SET TRANSMITTER BUTTON OPTIONS

ANTENNA

CONNECTOR

(HIDDEN)

RADIO RANGE KNOB

(CLOCKWISE FOR

MAXIMUM GAIN)

MAX

RADIO

TEST POINTS

GND

AUDIO

RADIO INDICATOR

STATUS INDICATOR

RED = HOLD, GREEN = DECODE

POWER AND

DATA TERMINALS

OPTION

DIPSWITCHES

INPUT

VOLTAGE

JUMPER

PROGRAM

BUTTON

PLACE VOLTAGE INPUT JUMPER

IN THIS POSITION TO SELECT A

REGULATED 5 VOLT DC INPUT

FROM THE ACCESS CONTROL

PANEL

PLACE VOLTAGE INPUT JUMPER

IN THIS POSITION TO SELECT A

8-24 VOLT DC INPUT FROM THE

ACCESS CONTROL PANEL

SELECT THE WIEGAND OUTPUT FORMAT

THAT MATCHES THE ACCESS CONTROL

SYSTEM BEING USED

SWITCH 1 26-BIT

SWITCH 2 30-BIT

SWITCH 3 31-BIT

RECEIVER OPTIONS

WIEGAND OUTPUT FORMAT

SWITCH 1 - LOCKOUT DISABLE

SWITCH 2 - HOLD ENABLE

SWITCH 3 - BUTTON OFFSET ENABLE

OFF

- (FACTORY SETTING) CAUSES RECEIVER TO IGNORE TRANSMITTER SIGNALS FOR ONE SECOND AFTER A VALIDATED TRANSMISSION.

- ALLOWS RECEIVER TO PASS WIEGAND DATA INSTANTLY WITH EACH VALIDATED TRANSMISSION.

OFF

- (FACTORY SETTING) HOLD INPUT SIGNALS ARE IGNORED.

- WHEN HOLD INPUT IS ACTIVE, ANY WIEGAND DATA WILL BE HELD FOR A MAXIMUM OF ONE SECOND THEN DISCARDED UNLESS THE

HOLD INPUT IS RELEASED DURING THE ONE SECOND TIME.

OFF

- (FACTORY SETTING) TRANSMITTERS PASS THEIR ID NUMBER TO THE WIEGAND OUTPUT WITHOUT ANY CHANGES.

- THE TRANSMITTER ID IS OFFSET TO THE RANGE ABOVE, BASED ON WHICH BUTTON IS PRESSED.

BUTTON OFFSET TABLE

LEFT

RIGHT

TOP

BOTTOM LEFT OR RIGHT

16384 32768 49152

= S W I T C H O N

SET XMTR FACILITY CODE

SWITCHES TO MATCH THE FACILITY

CODE PRE-PROGRAMMED INTO

TRANSMITTER BLOCK

NOTE: THE FACTORY SETTINGS

OF FACILITY CODE "0" WILL

ALLOW VALIDATION OF ANY

TRANSMITTER FACILITY CODE

S W T 0

S W T 1

S W T 2

S W T 3

1 0

1 1

1 2

1 3

1 4

1 5

TRANSMITTER BLOCK

FACILITY CODE 0-15

(ASSIGNED WHEN

TRANSMITTER BLOCK IS

ORDERED FROM LINEAR)

= S W I T C H O F F

XMTR FACILITY

CODE SWITCHES

BOTH

FUNCTION

AS LEFT

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

TOP

BUTTON

TOP

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

BOTTOM-RIGHT

BUTTON

BOTTOM-LEFT

BUTTON

LEFT

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

OPERATE

AS TOP

BUTTON

THE FACTORY SETTING ALLOWS ALL

TRANSMITTER BUTTONS TO OPERATE

SET XMTR BUTTON DISABLE SWITCH(ES) ON TO

PREVENT SELECTED TRANSMITTER BUTTONS

FROM OPERATING

SWITCH 4 - TOP

SWITCH 5 - BOTTOM RIGHT

SWITCH 6 - BOTTOM LEFT

SWITCH 7 - RIGHT OR TOP RIGHT

SWITCH 8 - LEFT OR TOP LEFT

1 2

Summary of Contents

Page 1 - Receiver

INSTR,INST,WORLinear P/N: 212902 CMaterial: 20 Lb. Mead BondSize: 8.500" x 11.000"Ink: BlackSide 1 of 2Scale: 1-1WORWiegandOutputReceiverIns

Page 2 - TRANSMITTER FACILITY CODE

INSTR,INST,WORLinear P/N: 212902 CMaterial: 20 Lb. Mead BondSize: 8.500" x 11.000"Ink: BlackSide 2 of 2Scale: 1-17. SET OUTPUT FACILITY CODE

Comments to this Manuals

No comments

Keri-systems RLB-500 User Manual

Browse online or download User Manual for Hardware Keri-systems RLB-500. Keri Systems RLB-500 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Keri-systems RLB-500